Learning Center How to Compare Mattresses
The Best Mattress for Arthritis, Joint Pain and Aches

The best mattress for arthritis, in one paragraph
The best mattress for arthritis is one that spreads your weight so no single joint is carrying it, springs back the moment you move so you are not climbing out of a dent every time you turn over, and can be changed after you have slept on it. That last part matters more than anything on a spec sheet. Nobody can tell you over the phone exactly how firm your bed should be, and we are not going to pretend otherwise. What we can do is build it out of separate layers of latex you can swap one at a time, so the bed follows your joints instead of the other way round.
Lee Carter: latex is the best for fibromyalgia sufferers and, if soft, best for pressure point relief.
Everything below is about support and pressure, which is what a mattress does. We build mattresses in Roanoke, Virginia and ship them nationwide.
Why being able to change it later is the whole point
A glued together mattress gives you one answer forever. If it turns out to be too firm under your hip, your choices are a topper on top of the problem or a return shipment. That is a hard bet to make when the joint that hurts is not the same joint it was last year.
Our mattresses are three or four separate layers of latex inside a cover that zips around all of it. Each layer has its own firmness, and you can order a different one and change it yourself. The cover stays, the base stays, the layer that is in the wrong place goes. If you want to see how that is put together before you read any further, you can build your mattress layer by layer on screen and watch the firmness change as you click.
The six firmness names are Ultra Soft, Soft, Medium Soft, Medium, Medium Firm and Ultra Firm. They are the same names whether you are picking a top layer, a middle layer, a bottom layer or a base layer, which keeps the conversation simple when you call and say the top is half a step too firm.
Pressure on a sore joint, and why turning over is the real test
Lie on your side on something too firm and your weight lands on two narrow places, the point of the shoulder and the point of the hip. Lie on something too soft and you sink until your waist is holding you up, and the shoulder and the hip are still carrying the load, just lower down. What you are after is a surface that gives way under the shoulder and the hip and stays put under the waist, so the weight is shared along the whole side of your body instead of stacked on two joints.
Then there is the part that rarely makes it onto a mattress page. Turning over. Memory foam keeps the shape of where you were lying for a moment after you leave it, so rolling onto your other side means pushing up out of a hollow. Latex does not behave that way. It pushes back as soon as the weight comes off it, so the surface is flat again by the time your shoulder gets there. If the hardest moment of your night is the one where you change position, that difference is the thing to pay attention to, and our page on latex foam compared with plastic foam goes into how the two materials differ.
It is also why a very soft bed is not automatically the kind answer. A deep soft surface can feel wonderful for the first ten minutes and then ask you to do work every time you move. Soft on top, supported underneath, is a different thing from soft all the way down.
Where to start, by what you are actually searching for
Arthritis is a broad word, and the searches people type are more specific than that. Osteoarthritis, rheumatoid arthritis and fibromyalgia are different things, and they do not all point at the same firmness. Here is how we would talk it through on the phone.
Osteoarthritis
This tends to show up in the joints that carry you: hips, knees, the lower spine. If those are your joints, you are weighing two things against each other. You want a surface soft enough that the hip is not pressed against a hard plane, and enough support under it that the hip is not dropping lower than the rest of you. That is the shape of Arrangement Recommendation 3, which is a Medium Soft layer on top over two Medium Firm layers, so the shoulder and hip sink in while the back stays supported. If after a couple of weeks the top still reads as too firm, the top layer is the thing you change, not the bed.
Rheumatoid arthritis
Here the joints that are sore can move around from month to month, and the smaller ones in the hands, wrists, feet and ankles come into it alongside the big ones. A bed you chose for how your shoulder felt last winter may not be the bed you want next summer. This is the clearest case for layers that come apart. You keep the cover and the layers that are working and you change the single layer that is in the wrong place. You are not buying a second mattress and you are not living with the first one.
Fibromyalgia
If this is what sent you looking, watch how the surface behaves across your whole body rather than at one joint. Tenderness that is spread out means a surface that presses anywhere is a problem, and a surface you sink into is a problem too, because getting out of the dip takes effort. Soft on top over something that still holds you up is the sensible place to begin, and that is Arrangement Recommendation 2: a Soft layer over two Medium layers. It is also our most popular arrangement, for the plain reason that it is comfortable without being too soft or too firm.
One joint, not all of them
A hip, a shoulder or a knee that hurts on its own is a different shopping problem from aching all over, and it is worth saying out loud which one it is before you pick. A side sleeper with a sore shoulder wants give in the top couple of inches, right where the shoulder lands, and firmness below that so the body does not fold. A back sleeper whose lower back is the problem usually wants less give, so the middle of the body is not the lowest point in the bed. Those two people should not order the same mattress, and there is more on that in our piece on comfort and side sleeping.
If what you are dealing with is sciatica or a herniated disc, that is a back question rather than a joint question, and our back pain guide takes each one in turn.
Chronic pain and general body aches
When the answer to “where does it hurt” is “everywhere, some days”, the honest advice is to start in the middle and keep the ability to move. Starting at an extreme and being wrong costs you the most. Starting at Medium or near it and then moving one layer half a step in either direction is a smaller, cheaper, less frustrating correction, and it is the correction our beds are designed to let you make.
The four arrangements, plainly described
These are the four builds we sell most often. Every one of them is three layers of certified latex inside a Tencel and polyester cover, and every one of them can be changed layer by layer afterwards. All four start at $1,300 and the price depends on the size and the number of layers.
| Arrangement | Layers, top to bottom | Who it is built for |
|---|---|---|
| Arrangement Recommendation 1 | Ultra Soft, Medium Soft, Medium Soft | Our softest. Plush and cradling, made for lighter body weights or anyone who wants to sink in. |
| Arrangement Recommendation 2 | Soft, Medium, Medium | Our most popular, because it is extremely comfortable without being too soft or too firm. An all round starting point. |
| Arrangement Recommendation 3 | Medium Soft, Medium Firm, Medium Firm | Firm support with a cushioned top, so the shoulder and hip sink in while the back stays supported. |
| Arrangement Recommendation 4 | Medium Firm, Ultra Firm, Ultra Firm | Our firmest, for heavier body weights or anyone who wants a truly firm bed. |
If you would rather compare them properly, with the descriptions and the prices in one place, you can see the four arrangements side by side. And if none of the four is quite it, you are not stuck with the four. Three layers with six firmness choices each is a very large number of combinations, and the configurator will build any of them.
For every layer and firmness laid out in one place, see our mattress comparison chart.
Picked your starting point? All four arrangements are on one page, and every one can be changed layer by layer.
See the four arrangements side by sideSee the AR2, our most popular
What is actually inside it
The layers are GOLS certified organic latex. That certificate covers the latex itself, the material your joints rest on all night, and you can read exactly what the latex certificate covers or the longer account of the organic latex we use and how it is certified. There are no fire retardant chemicals in it. Sleep Essentials is the only maker building beds entirely without them.
Our beds are built without fire retardant chemicals, without glass fibre, and without silica treatments. The latex is not blended with synthetic fillers. The cover is Tencel and polyester, and it zips around the layers so the inside is reachable.
It is a list of what is and is not in the mattress, which you are entitled to know before you sleep on it for ten years.
Two people, two different sets of joints
If your joints and your partner’s joints want different beds, you do not have to split the difference and leave both of you unhappy. Split firmness beds let you choose an arrangement for each side, with side B as the firmer side. They start at $2,150. Split Florida King and Split Family King come in 9 or 12 inches, and every other size comes in 9 inches.
The same logic applies afterwards. If one side needs a change in a year, one side gets the change.
Getting it wrong is meant to be survivable
You are going to make this decision from a page on a screen, and no page can tell you how a mattress will feel at four in the morning in the third week. So the useful question is not “how do I get it right first time”, it is “what happens if I am half a step off”.
- You sleep on it. Not for two nights. Give it a couple of weeks, because a new surface always feels like a new surface at first.
- You work out which layer is wrong. Usually it is the top one, and usually it is one step, not three.
- You order that layer and change it yourself. The cover unzips, the layer comes out, the new one goes in.
Behind that there is a 60 day comfort assurance and a 10 year non prorated warranty, both of which are written out in plain terms rather than buried.
Talk to the person who builds it
The phone is worth using for this one. Call 540-397-2337 and you can talk to the person who builds these mattresses, say which joint is the problem and which position you sleep in, and get a straight recommendation on which arrangement to start from. It is a free sleep consultation and there is no obligation attached to it.
If you would rather read first, everything in the Learning Center is laid out by topic, from how to compare mattresses to what is actually inside one.
Why this latex suits sore joints
Lee Carter built this mattress for people whose joints hurt, and he is direct about what it is best at. The latex is best for fibromyalgia sufferers. It is best for pressure point relief. And it is the best mattress to prevent bed sores for people with mobility issues, because the surface gives under a hip or a heel instead of pressing back against it and the latex returns to shape the moment the weight moves.
That last one matters most for anyone who cannot shift position easily on their own. Pressure that never moves is what does the damage, so a surface that spreads the load and springs back is doing the work a carer would otherwise be doing by hand.
Best mattress for fibromyalgia
Latex is the best for fibromyalgia sufferers and if soft, best for pressure point relief. Those are Lee Carter’s own words. With fibromyalgia the tenderness is spread across the whole body, so the surface has to give wherever you touch it and still hold you up underneath, and it has to spring back so turning over is not a climb out of a dip.
Start with the AR2, a Soft layer over two Medium layers. It helps reduce pressure points on your hips and shoulders, and it is our most popular arrangement. If you are lighter or want to sink in further, the AR1, our softest, puts Ultra Soft on top, and Lee says you will easily be able to put muscle aches and joint pain from your day to rest on it.
Best mattress for rheumatoid arthritis
A latex foam rubber mattress is the best mattress for someone with rheumatoid arthritis. That is how Lee puts it. The sore joints can move around from month to month, so a bed built from separate layers lets you change the one layer that is wrong instead of buying a second mattress.
Start with the AR2, or the AR3 if you want firm support with a cushioned top: Medium Soft over two Medium Firm layers, so your shoulders and hips sink in while your back stays supported. Once you know how it feels, change the top layer one step in whichever direction you need.
Best mattress for pressure points
Latex is best for pressure point relief, and soft latex most of all. Pressure points are the places your weight lands hardest: the shoulder and the hip when you are on your side. A soft latex top layer gives way under those points and pushes back the moment the weight comes off, while firmer layers underneath keep you level.
Lee’s AR2 arrangement is built for exactly this: it helps reduce pressure points on your hips and shoulders, making it ideal for side sleepers. The AR3 does the same over firmer support. Its multi layer design creates pressure relief points, the cushiony top layer absorbs any pressure you put on it throughout the night, and the middle layer provides a pressure relief point of its own.
Best mattress to prevent bed sores for people with limited mobility
A latex foam rubber mattress is the best mattress to prevent bed sores for people with mobility issues. That is Lee’s claim, in his words. Someone who cannot turn over easily on their own leaves their weight on the same places for hours, so the surface has to spread that weight out and give under a hip or a heel instead of pressing back against it.
Soft latex on top does that, and it returns to shape the moment the weight moves. Start with the AR1, Ultra Soft over two Medium Soft layers, or the AR2, Soft over two Medium layers. Call 540-397-2337 and tell us the person’s weight and how much they can move on their own, and we will tell you which one to build.
Arthritis, fibromyalgia or sore joints: start with one of our four arrangements and change a layer when you need to.
See the 4 Most Popular Organic Latex Mattresses, From $1,300Call the person who builds them: 540-397-2337
Common questions
What is the best mattress for arthritis?
A latex mattress built in separate layers, started at a firmness that suits your weight and sleeping position, and then adjusted a layer at a time once you have slept on it. Latex springs back instead of holding a dent, so you are not pushing out of a hollow when you turn over, and layers mean the firmness is a decision you can revisit rather than one you are stuck with.
What is the best mattress for rheumatoid arthritis?
The same construction, chosen for the same reasons, with the layers mattering even more. When the sore joints change from month to month, the ability to change one layer rather than the whole bed is the practical advantage. A sensible place to start is Arrangement Recommendation 2 or 3, then move the top layer one step once you know how it feels.
What is the best mattress for fibromyalgia?
Look for soft on top with real support underneath, rather than soft all the way down. Widespread tenderness means you want the weight spread out, and you also want to be able to change position without hauling yourself out of a dip. Arrangement Recommendation 2, a Soft layer over two Medium layers, is the usual starting point.
What is the best mattress for joint pain in one hip or shoulder?
Pick for the position you sleep in. Side sleepers with a sore shoulder or hip want give in the top layer, where the joint actually lands, over firmer layers underneath. Back sleepers want less give so the middle of the body is not the lowest point. Tell us which joint and which position and we will tell you which arrangement to start from.
Is a soft or a firm mattress better for aches and pains?
Neither one wins on its own, which is why the question keeps going round. Too firm and your weight lands on the narrow points of the shoulder and hip. Too soft and you sink into a shape you then have to climb out of. What usually makes sense is a softer top layer over firmer support, so the shoulder and hip have somewhere to go while the rest of you is held up. The right amount of softer is the part you adjust afterwards.
What is the best bed for osteoarthritis?
A build with a cushioned top over firm support, so the hip and shoulder are not pressed against a hard surface while the rest of you is still held up. Arrangement Recommendation 3 is that shape: Medium Soft over two Medium Firm layers. If the top is still firmer than you want, change the top layer.
What is the best mattress for chronic pain and body aches?
Start near the middle rather than at an extreme, and keep the ability to move. If the answer to where it hurts changes from day to day, the thing with real value is not a particular firmness but a bed where one layer can be swapped for the next step up or down without replacing anything else.
What if I choose the wrong firmness?
Then you change a layer, which is the point of building it this way. Sleep on it for a couple of weeks, work out which layer is wrong and in which direction, order that layer, unzip the cover and swap it. The 60 day comfort assurance covers the period while you are working it out.
Can I use these with an adjustable bed?
Yes. We sell adjustable bases as well as mattresses, and the layered latex builds work on them. If raising your head or your knees is part of how you get comfortable, mention it when you call, because it can affect which arrangement we would point you at.
Looking for something else? Read our answers to back, hip and shoulder pain questions.
